View Gardening .com

World of Mowers. They do free delivery anywhere in the UK.

http://www.worldofmowers.ltd.uk/P/Hayter Murray-Tractor-Belt-Part-No-37-x-74(1824 ).aspx

2009-07-31 07:42:28 by chippieandy

Test run and mow of the Murray/MTD mower that had the head repair done.

Hey I was wondering if any of you would know where I could find either deck parts, or a used mower deck that would fit on a 1976 or equivilant riding lawn mower?? I need a pully, and a quill set.

Try www.mfgsupply.com for mower parts. They cover all types of lawn mowers and other small engine equipment

2008-06-18 20:57:23 by Carguy2005

Price: $19.99 $17.49

Murray Part Number 495100
3-n-1 Combination Blade can be Used for Side Discharge, Mulching, or Bagging
Also Replaces Murray Part Numbers 95100E701; 95100-853, 92545E701, 456252, and 56252E701

I have a 16.5 hp Murray riding lawnmower. Brakes dont work to good. How do i adjust or replace them. Part names or numbers that I should replace? thank you

If your mower is not really old, they probably just need to be adjusted. I believe you need a 1/2" or 9/16" wrench or socket to tighten them. The adjusting nut is just under the rear of the tractor near the right rear tire. You need to jack the back of the tractor up slightly. It can be done without jacking, but it is harder to find the nut. You will see the brake rod coming from the front of the tractor. The brake itself is held on by two bolts, between those two bolts, is the adjusting nut. Tighten the nut slightly. Apply the brakes to see if they are working, if not, tighten a little more. Do not over tighten, or you will not be able to push the tractor when it is in neutral and the brake is off.

2007-01-21 17:45:33 by BigRey

Price: $21.99 $18.65

Blade Drive Belt for 42" Murray Decks from 1997 to Present
Genuine Murray Part
Blade Drive Belt for 42" Scotts Decks from 1997 - 2000

it was given to me taken apart. In trying to put it back together the pull cord spins freely. I am pretty sure all the parts are there. It has a electric start, but i took that off and decided i would just crank it with the pull cord. The pull cord bolts down on the crank shaft (i guess its called) the shaft is just an open bell shaped metal bowl that the plastic pull cord bottom fits in, but it spins freely. anyone know how to get it to crank?

If it's not the engine as the poster above mentioned, it might be that you forget some parts in the starter clutch?

If it's a Briggs you will have a big square post on the top of the flywheel that goes into the retracting cord spool. The post should lock to the shaft in 1 direction and freewheel in the other.

The post rides in a notched cup and 6 ball bearings that grab the notches on the post as you start it and are flung free to the outside edge of the cup when it's running. The ball bearings can get rusted in place if the mower was left in the rain a lot.

If that was the original problem, you can get to them by removing the four 1/4 inch screws around the top of the flywheel that hold the circular metal screen in place. Lift off the screen then the plastic bearing cover (you may need to pry a bit). You should now see the balls and pawls. The post can be pulled up and off the shaft.

Here hoping you get it figured out!

2008-07-16 12:11:31 by Tmoney438

Hi! I need help finding out how to repair my AutoDrive 42" 17HP Murray Riding Lawn Mower Widebody LT. We were mowing and hit something, the blade broke and the part or parts that holds the blade is broke/loose. Can someone please tell me what parts I will need to fix this. Any help would be greatly appreciated! Thank you.....

Model #425303X92
Serial #7475501621R199
MFG Date 02016
3-way Cutting Deck

Best way to see whats happened - pull the deck off. Heres a link to your lawntractors parts list :http://jackssmallengines.com/help.cfm - type in your model number under 'model' section - it appears you have a 2002 model.
Your 'mandrel' or deck spindle assy part number is :1001200MA - if you need a blade :095100E701MA - if you need a pulley -494199MA. Most lawntractors sometimes have a small block that bolts to the end of the spindle assy - apparantly yours dosent ( its designed that way). To replace the mandrel , its probably in the $60 range , pulleys( if needed) are like $15 - if a new blade is needed ( buy a set- not just one) theyre usually around $10-20 ( depending if its a mulching blade - theyre more - i bot two for my Murray and they were like $18 a piece). Any tractor parts place should be able to get those parts - ive also seen them at Tractor supply.
While the deck is off, it probably would be a good time to clean it, check the other mandrel housings/berings- replace if needed.

2007-09-22 09:00:31 by nwiebe36